Sunday, September 8, 2013

Trammel-Jig Trivets


I found this idea for making attractive wood trivets in the magazine called woodworkers Journal issue winter of 2013.
The jig is fairly straight forward but you do have to read the text a couple times to make sure you understand the instructions properly, or at least I did. The size of the wooden blanks is critical in order to make this jig work properly as is the distance from the pivot point on the trammel to the outside edge of your chosen router bit. The spacers are also critical so make sure when you make them that you do them all at once or be very careful if you need to do two batches.


The first picture shows the jig which is the 22 x 22" plywood sheet with the 90° corner attached to it. The corner and the axis for the trammel need to be lined up to the corners of the 22 inch square to make sure that the router cuts the semicircles consistently.

This picture shows the position of the blank to be cut and the V notched hold down to prevent the blank from skidding around on the plywood.


I glued 100 grit sandpaper on the top to prevent the wood from sliding around while routing it.

The instructions suggested a 1/2" spiral up cut bit but I don't have one on hand . Instead I used a 3/8" cutter and it seems to be just fine.


The first mistake I made was not giving myself a line around the trivet on which to stop the cut. I found it difficult if not impossible to see inside the router chamber and determine exactly where  that was without a headlamp and a nice dark pencil line to follow.

The second mistake involved not setting the depth of cut stop securely on the router. After a couple of cuts the bit eased out and spoiled the first bank.

I also found that making several passes with the router produced a cleaner and sharper groove that just dropping the bit and plowing through the wood. There was negligible burning this way as well.



I started to hit my stride on the third attempt and shown here are two examples that made the grade.

With Christmas coming up you may want to give this project a try and make some useful stocking stuffers.

They sure to be a hit with the cooks in your family.












I managed to get 2 pieces cut so far as I had to mill pieces of walnut and Manitoba maple to 1/4" thickness and glue them up before cutting blanks. The trivet on the right has an extra piece of walnut down the center as I couldn't find any 6" stock in my horde. It is coated with Claphams salad bowl finish but I will just use mineral oil on the rest I think.
 This is a shot of the trammel showing the peg on which it pivots. Note the 1/2' stick at the right end of the jig that serves to land the router at the end of each pass.
 This picture shows the carbide cutter just clearing the walnut to expost the lighter maple wood.
 This shows the set up for cutting the opposing side of the trivet.



This one looks like it will do. A little deeper on one pass but I will live with it.



2 comments:

Blogger said...

Get immediate access to 16,000 woodworking plans.

Teds Woodworking has over 16,000 woodworking plans with STEP BY STEP instructions, sketches and blueprints to make all projects easy and simple!

Blogger said...

Do you understand there's a 12 word phrase you can say to your crush... that will trigger intense feelings of love and impulsive appeal for you buried within his heart?

That's because deep inside these 12 words is a "secret signal" that fuels a man's impulse to love, worship and look after you with all his heart...

===> 12 Words Will Trigger A Man's Love Impulse

This impulse is so built-in to a man's genetics that it will make him work better than before to take care of you.

As a matter of fact, triggering this mighty impulse is so binding to achieving the best ever relationship with your man that once you send your man one of these "Secret Signals"...

...You'll immediately notice him open his mind and heart for you in such a way he never experienced before and he'll perceive you as the only woman in the galaxy who has ever truly fascinated him.